Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of Ultramid® B3WG8 BK00564 - PA6-GF40 - BASF

Check here, which other Ultramid B datasheets, application examples or technical articles are available in Material Data Center

Caracteristicas de procesamiento y fisicas - Propiedades mecánicas - Propiedades térmicas - Propiedades eléctricas - Otras propiedades - Funciones

Any use of this information falls under the rules of our disclaimer.

Texto del producto

Glass fibre reinforced and heat aging resistant injection moulding grade, e.g.used for automobile parts with high stiffness requirements under the hood.
The products can also be offered as BMBcert™ and/or Ccycled™. Due to the Massbalance approach the product properties do not change.

Caracteristicas de procesamiento y fisicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Indice de fluidez volumétrico, MVR	20 / *	cm³/10min	ISO 1133
Temperatura	275 / *	°C	-
Carga	5 / *	kg	-
Contracción posterior al moldeo, paralelo	0.3 / *	%	ISO 294-4, 2577
Contracción posterior al moldeo, normal	0.8 / *	%	ISO 294-4, 2577

Propiedades mecánicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Módulo de tracción	12700 / 7700	MPa	ISO 527
Resistencia a la tracción	205 / 125	MPa	ISO 527
Alargamiento a rotura	3 / 5.5	%	ISO 527
Módulo de plastodeformación, 1000h	* / 5400	MPa	ISO 899-1
Resistencia al impacto Charpy, +23°C	95 / 95	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy, -30°C	85 / 85	kJ/m²	ISO 179/1eU
Resistencia al impacto Charpy c/entalla, +23°C	13 / 20	kJ/m²	ISO 179/1eA
Resistencia al impacto Charpy c/entalla, -30°C	10 / 10	kJ/m²	ISO 179/1eA

Propiedades térmicas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Temperatura de fusión, 10°C/min	220 / *	°C	ISO 11357-1/-3
Estabilidad al calor, 1.80 MPa	210 / *	°C	ISO 75-1/-2
Estabilidad al calor, 0.45 MPa	220 / *	°C	ISO 75-1/-2

Propiedades eléctricas	Seco / Cond	Unidades	Método de ensayo
ISO Data
Resistencia dieléctrica	40 / 31	kV/mm	IEC 60243-1

Otras propiedades	Seco / Cond	Unidades	Método de ensayo
Absorción de agua	5.45 / *	%	Sim. to ISO 62
Absorción de humedad	1.8 / *	%	Sim. to ISO 62
Densidad	1460 / -	kg/m³	ISO 1183

Funciones

Características

Procesamiento y forma de entrega

Moldeo por inyección

Forma de suministro

Sémola, Negro

Aditivos

Lubricante, Desmoldeante

Características especiales

Estable contra el calor

Applicaciones

Automotriz

Disponibilidad regional

Europa

Demás información

Moldeo por inyección

PREPROCESSING
Pre/Post-processing, max. allowed water content: .15 %
Pre/Post-processing, Pre-drying, Temperature: 80 °C
Pre/Post-processing, Pre-drying, Time: 4 h

PROCESSING
injection molding, Melt temperature, range: 270 - 290 °C
injection molding, Melt temperature, recommended: 280 °C
injection molding, Mold temperature, range: 80 - 90 °C
injection molding, Mold temperature, recommended: 80 °C
injection molding, Dwell time, thermoplastics: 10 min

Disclaimer

Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.

Created: Source: www.materialdatacenter.com

Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.